亚洲特黄无码一级氏毛片,一区二区三区国产美女在线播放,韩国一级片国产亚洲,91女厕偷拍一区二区三区老牛影视

您好,歡迎光臨河北安恕朗盛機械科技有限公司網站!

為中國高凈值客戶和機構提供可靠的、持續高效服務

Around you

Financial Management Expert

獨具魅力和特色的現代化規模型企業

團結、創新、誠信、務實!     過硬的產品,優質的服務,合理的價格!

雄厚實力 科學管理、先進的營銷理念和良好的信譽! 

 

對外貿易 自主研發 非標定制

咨詢熱線
15203283906
普洱GICLZ聯軸器
普洱GICLZ聯軸器
普洱GICLZ聯軸器
所屬分類:普洱聯軸器
發布日期:2/9/2018
瀏覽:4197次
咨詢電話:
河北安恕朗盛機械科技有限公司

g1clz002

聯軸器適用于聯接水平兩同軸線,并具有一定角向位移的傳動軸系。當被聯接兩軸端相距較遠時適用于采用CICLZ型,傳遞公稱轉矩為0.8~32000KN.m,工作環境溫度-20~+80℃
鼓形齒式聯軸器的特點
  
齒式聯軸器是由齒數相同的內齒圈和帶外齒的凸緣半聯軸器等零件組成。外齒分為直齒和鼓形齒兩種齒形,所謂鼓形齒即為將外齒制成球面,球面中心在齒輪軸線上,齒側間隙較一般齒輪大,鼓形齒聯軸器可允許較大的角位移(相對于直齒聯軸器),可改善齒的接觸條件,提高傳遞轉矩的能力,延長使用壽命。有角位移時沿齒寬的接觸狀態。
齒式聯軸器在工作時,兩軸產生相對角位移,內外齒的齒面周期性作軸向相對滑動,必然形成齒面磨損和功率消耗,因此,齒式聯軸器需在有良好和密封的狀態下工作。齒式聯軸器徑向尺寸小,承載能力大,常用于低速重載工況條件的軸系傳動,高精度并經動平衡的齒式聯軸器可用于高速傳動,如燃汽輪機的軸系傳動。由于鼓形齒式聯軸器角向補償大于直齒式聯軸器,國內外均廣泛采用鼓形齒式聯軸器,直齒式聯軸器屬于被淘汰的產品,選用者應盡量不選用。
I型-密封端為分離型,齒間距較大,可以允許較大的徑向位移,可與Y、J1、Z1型軸伸聯接。
型-密封端為整體型,齒間距小,相對允許徑向位移小,結構緊湊,轉動慣量小,可與Y、J1型軸伸聯接。


This coupling is applicable to the two coaxial lines of the connection level and the transmission shafting with a certain angular displacement. When the connection is far away from the shaft end is suitable for adopting CICLZ type, transfer the nominal torque 0.8 ~ 32000 kn. M, working environment temperature - 20 ~ + 80 ℃

Features of drum gear coupling

The gear coupling is composed of the same inner ring and the flange half coupling of the outer tooth. Divided into straight teeth and drum tooth outside two kinds of tooth shape, tooth is the so-called drum will made spherical outer teeth, spherical center on the gear axis, backlash is generally large gear, drum gear couplings allows a larger angular displacement (as opposed to straight tooth coupling), can improve the tooth contact conditions, improve the ability to transfer torque, prolong service life. The contact state along the tooth width in angular displacement.

Low coupling at work, two relative angular displacement of the shaft of the internal and external gear tooth surface of periodic axial relative sliding, inevitable formation of tooth surface wear and power consumption, therefore, the coupling should be in good and sealing state work. Type coupling radial size is small, large carrying capacity, often used for shaft transmission of working condition of low speed and heavy loading, high precision and the dynamic balance of coupling can be used for high-speed transmission, such as gas turbine shaft transmission. Because the drum type coupling Angle is greater than the direct coupling to the compensation, both at home and abroad widely used drum type coupling, straight type coupling are eliminated products, choose those should not choose as far as possible.

The type I - sealing end is the separation type, the tooth spacing is larger, can allow larger radial displacement, can be connected with Y, J1, Z1.

Ⅱ - sealed end to overall, tooth spacing is small, relative to allow the radial displacement is small, compact structure, and the moment of inertia is small, can be connected to Y, J1 type shaft extension.




5


上一個:普洱JZM聯軸器
下一個產品:普洱WGP聯軸器